Thread Closed 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
SR100 Software Update SDR200707152118
01-23-17, 04:03 PM
Post: #1
SR100 Software Update SDR200707152118
SR100 Software Update SDR200707152118

SR100 Audio Software Update for E-Series
Raymarine released a single software update for the SR100. This software update was designed to add support for Sirius Satellite Radio. This software update was only designed to be performed via an E-Series Classic MFD and had been included with software E-Series Classic MFD v4.29 software download. The latest software release for the SR100 is version SDR200707152118 released in January 2008.

Upgrading the SR100 using a E-Series Display Unit
The SR100 software can be upgraded through a connection to an E-Series display. The upgrade requires a blank CompactFlash card and a CompactFlash reader/writer.
To complete the software upgrade you must have all of the following parts:
• Any E-Series Multifunction Navigation Display (E80 or E120)
• SeaTalk High Speed Network Cable (These are available in four lengths)
o E55049 (1.5 meters)
o E55050 (5 meters)
o E55051 (10 meters)
o E55052 (20 meters)
The cables are available through any Authorized Raymarine Dealer. In North America the cables can be ordered directly from Raymarine Customer Service by calling 603-881-5200 ext. 2333
• A San Disk brand Compact Flash (CF) memory card (32MB - 256MB)
• A Compact Flash reader/writer
• A Microsoft Windows or Macintosh computer
• E-Series Classic MFD updated with v4.29 and SR100 Upgrade SDR200707152118.

Upgrade Instructions:

1. Download the attached WinZip file. Extract the contents of the WinZip file to the root level directory of the Compact Flash memory card.

2. This step intentionally left blank

3. Power off both the E-Series display and the SR100.

4. Connect the E-Series display to the SR100 via the SeaTalkhs cable. If you SR100 and ESeries are already installed and connected to the SeaTalkhs Network Switch, you do not
need to disconnect them.

5. Insert the CF card into the E-Series card reader. Power the display on.

6. The status LED on the SR100 must be blinking amber or green. Sirius antenna does not have to be connected to perform upgrade.

7. Use the E-Series track pad to highlight the file named “SR100 v1.1” in the left column.

8. Press the Upgrade Remote Unit soft key.

9. Press the Upgrade Remote Unit on “Ethernet” soft key. The Upgrade progress bar appears.

10. The progress bar will begin updating. If they do not begin updating within 30 seconds, check:
.....a. that the correct software revision was selected.
.....b. that the SR50/SR100 weather receiver is powered ON and status LED is flashing.
.....c. that the display/weather receiver data cable connection is intact.

11. When the update process is complete, remove the CF card from the card reader slot.

12. Press the CLEAR key one time, and then Press the REBOOT soft key. Your display will restart automatically. Your SR100 weather receiver system and display are now ready for normal operation. For full details of how to operate your SR100 Weather and Audio Application refer to the E-Series Multifunction Display handbook. A copy of this manual is available here.

Confirming a Successful Upgrade
Beyond normal operation, successful upgrade to the SR100 can be confirmed through the ESeries’ on-board diagnostic features.
• Restart both the E-Series display and the SR100 by switching them off, then on.
• On the E-series press MENU, and then select SYSTEM DIAGNOSTICS.
• Select EXTERNAL INTERFACES, then SIRIUS WEATHER.
• On the second line of the RX Status window, the “SDR Software Version” should read SDR200707152118
• Press CLEAR several times to exit the menus.


RAYFAQ#


Attached File(s)
.zip  SR100_SDR200707152118.zip (Size: 2.09 MB / Downloads: 570)
Find all posts by this user
Thread Closed 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)