Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
GPS Connection
09-28-16, 05:23 AM
Post: #1
GPS Connection
Is this correct for wiring a NMEA version Raystar 120 to an AIS 650?

120 black to AIS yellow.
120 yellow to AIS gray

Then the AIS pink and purple to NMEA 4800 baud equipment such as radios.

Thank you.
Find all posts by this user
Quote this message in a reply
09-28-16, 02:53 PM (This post was last modified: 09-28-16 02:54 PM by Chuck - Raymarine - Moderator.)
Post: #2
RE: GPS Connection
Welcome to the Raymarine Forum WWMS,

For the benefit of others who may be viewing this thread, the AIS650 is entirely dependent upon its internal GPS receiver circuitry and supplied passive GPS antenna to determine a GPS position FIX to be used in its AIS RF transmissions. The AIS650 is not designed to use GPS data from a NMEA 0183 or SeaTalkng/NMeA 2000 data source for such purposes. Should the purpose of interfacing the Raystar 120 NMEA 0183 GPS Sensor to the AIS650 be to multiplex GPS data with the AIS data for use with the MFD, then:

- NOTE: the 4800 BAUD NMEA 0183 output of Raymarine products may be paralleled to supply data to up to three NMEA 0183 listeners ... therefore, making is less complicated, not dependent upon operation of the AIS650, and more reliable to interface both the 4800 BAUD NMEA 0183 input of the AIS650 and VHF radio to the NMEA 0183 output of the Raystar 120 NMEA 0183 GPS Sensor.

- connect the red lead of the Raystar 120 NMEA 0183 GPS Sensor to a switched 12VDC power circuit which has been protected with a 0.5A fuse

- connect the ground (shield) lead of the Raystar 120 NMEA 0183 GPS Sensor to each of the following:
----- ground
----- AIS650 4800 BAUD NMEA 0183 IN- (yellow) lead
----- DSC VHF radio 4800 BAUD NMEA 0183 IN- lead

- connect the NMEA 0183 OUT+ (yellow) lead of the Raystar 120 NMEA 0183 GPS Sensor to each of the following:
----- AIS650 4800 BAUD NMEA 0183 IN+ (grey) lead
----- DSC VHF radio 4800 BAUD NMEA 0183 IN+ lead
Find all posts by this user
Quote this message in a reply
09-29-16, 07:39 AM
Post: #3
RE: GPS Connection
Thanks Chuck.

I just found out it is a Raystar 125, not 120. I think it can be wired as you describe above with the addition of brown and green also connected to ground. Is that correct? Thanks again.

Rich
Find all posts by this user
Quote this message in a reply
09-29-16, 10:07 AM (This post was last modified: 09-29-16 10:07 AM by Chuck - Raymarine - Moderator.)
Post: #4
RE: GPS Connection
Rich,

Given the same situation, but the GPS sensor be a Raystar 125 GPS Sensor, then the prior response would be amended to state the following:

For the benefit of others who may be viewing this thread, the AIS650 is entirely dependent upon its internal GPS receiver circuitry and supplied passive GPS antenna to determine a GPS position FIX to be used in its AIS RF transmissions. The AIS650 is not designed to use GPS data from a NMEA 0183 or SeaTalkng/NMEA 2000 data source for such purposes. Should the purpose of interfacing the Raystar 125 GPS Sensor to the AIS650 be to multiplex GPS data with the AIS data for use with the MFD, then:

- NOTE: the 4800 BAUD NMEA 0183 output of Raymarine products may be paralleled to supply data to up to three NMEA 0183 listeners ... therefore, making is less complicated, not dependent upon operation of the AIS650, and more reliable to interface both the 4800 BAUD NMEA 0183 input of the AIS650 and VHF radio to the NMEA 0183 output of the Raystar 125 GPS Sensor.

- connect the red lead of the Raystar 125 GPS Sensor to a switched 12 VDC power circuit which has been protected with a 0.5A fuse

- connect the brown and shield (black) leads of the Raystar 125 GPS Sensor to each of the following:
----- ground
----- AIS650 4800 BAUD NMEA 0183 IN- (yellow) lead
----- AIS650 4800 BAUD NMEA 0183 OUT- (pink) lead
----- DSC VHF radio 4800 BAUD NMEA 0183 IN- lead

- connect the NMEA 0183 OUT+ (yellow) lead of the Raystar 125 GPS Sensor to each of the following:
----- AIS650 4800 BAUD NMEA 0183 IN+ (grey) lead
----- DSC VHF radio 4800 BAUD NMEA 0183 IN+ lead

- connect the green lead of the Raystar 125 GPS Sensor to the AIS650 4800 BAUD NMEA 0183 OUT+ (purple) lead ... to support having the MFD command GPS restart
Find all posts by this user
Quote this message in a reply
09-29-16, 10:26 AM
Post: #5
RE: GPS Connection
Wow. Didn't expect that. Have a great day.

Rich
Find all posts by this user
Quote this message in a reply
09-29-16, 10:33 AM
Post: #6
RE: GPS Connection
You're welcome.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)