Post Reply 
 
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA11] Installation Diagram
10-28-18, 09:19 PM (This post was last modified: 10-29-18 10:35 AM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11] Installation Diagram
Very Good Night Raymarine Support Dept.

I need your help in a diagram of installation to know what connector or cable I need to make my installation correct, I have a 42-foot yacht with 3 outboard motors Mariner Verado 400, These are the equipment that I have and I want to leave connected and working properly.

E70345 Ray52 VHF Radio GPS Receiver 2
E70369-03-LNC AXIOM 12 RV 600W Sonar 1
E70368-00-LNC AXIOM 12 Multifunction Display 2
A80007 HS-5 Network Switch (RayNet) 1
T70157 EV-200 Hydraulic Autopilot 1
A62361 RayNet (F) to RayNet (F) cable - 2m. 1
T70408 4kW Magnum with 48" Open Array 1
E70354 M232 Pan and Tilt Thermal Camera. 1
T70327 RS150 GPS Antenna, w/Pole Mount Kit. 1

These are the equipment, what I would like to know is if I need some kind of switch or cable to leave everything ready in the shortest possible time.

Thanks for your help, and great support!
Find all posts by this user
Quote this message in a reply
10-29-18, 10:55 AM
Post: #2
RE: [CA11] Installation Diagram
Welcome to the Raymarine Forum Metxxx69,

Unfortunately, we don't have the bandwidth to produce custom diagrams. Certified Raymarine Installers may be able to provide such as part of the equipment installation. To interface the specified equipment, a HS5 RayNet Network Switch will indeed be required. Each MFD will be interfaced to the HS5 RayNet Network Switch via an an appropriate length of RayNet (F) to RayNet (F) Cable. The Digital Radar Cable will likewise be interfaced to the HS5 RayNet Network Switch. The FLIR M232 Thermal Camera's POE injector will be interfaced to the HS5 RayNet Network Switch via RayNet (F) to RJ45 (M) Cable.

A powered and properly terminated SeaTalkng / NMEA 2000 backbone will be installed and will have a sufficient number of spur sockets to permit each of the following to be interfaced as individual spurs to the backbone. The maximum length of cable to be included within a spur shall not exceed 6m:
- Axiom MFD which will be designated as the system's Data Master MFD. As the NMEA 2000 socket of the Axiom MFD is terminated with a DeviceNet (M) socket, an A06075 39.4in (1.0m) DeviceNet Female to SeaTalkng Spur Adapter will be used to interface the MFD to a spur socket.
- p70RS Autopilot Control Head
- EV-1 CCU
- ACU200
- Raystar 150 GPS Sensor (3m cable supplied)
- Ray52 VHF Radio.
Visit this user's website Find all posts by this user
Quote this message in a reply
10-29-18, 11:18 AM (This post was last modified: 10-29-18 12:18 PM by Chuck - Raymarine - Moderator.)
Post: #3
RE: [CA11] Installation Diagram
Thanks Mr. Chuck!

Always with the best and prompt responses!
Find all posts by this user
Quote this message in a reply
10-29-18, 01:05 PM
Post: #4
RE: [CA11] Installation Diagram
You're welcome.
Visit this user's website Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)

Contact Us