Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11] Multiple MFDs wth 50/200 kHz sonar
04-11-19, 07:19 AM (This post was last modified: 04-11-19 03:10 PM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11] Multiple MFDs wth 50/200 kHz sonar
I again have an Axiom RV and eS127 networked. I have the RV-100 connected to the Axiom and a B60 thru-hull connected to the eS127.

Q1 - Can I run the 50/200 kHz sonar at the same time on both units? The thru-hull B60 reads well at speeds so I would like to keep it as my preferred depth source.

Jack - MS Gulf Coast
Current Ray Equipment - Axiom 7 RV serving as DM and networked to a eS127 -
Quantum Radar via WiFi to eS127, RMK-9 networked to eS127, EV-1 Sensor Core, RV-100 and B60 transducers.
Find all posts by this user
Quote this message in a reply
04-11-19, 03:11 PM
Post: #2
RE: [CA11] Multiple MFDs wth 50/200 kHz sonar
Welcome back to the Raymarine Forum MSjack,

Q. Can I run the 50/200 kHz sonar at the same time on both units?
A. Yes.
Find all posts by this user
Quote this message in a reply
04-11-19, 03:37 PM
Post: #3
RE: [CA11] Multiple MFDs wth 50/200 kHz sonar
OK - was not sure if there would be any interference between the two if they were both set to 200. Or if one needed to be on 50?

Thanks as always.

Jack - MS Gulf Coast
Current Ray Equipment - Axiom 7 RV serving as DM and networked to a eS127 -
Quantum Radar via WiFi to eS127, RMK-9 networked to eS127, EV-1 Sensor Core, RV-100 and B60 transducers.
Find all posts by this user
Quote this message in a reply
04-12-19, 07:48 AM
Post: #4
RE: [CA11] Multiple MFDs wth 50/200 kHz sonar
Jack,

There's only one 50kHz/200kHz in the system. So displaying the 200kHz channel on both MFDs is simply going to result in the same image being presented on both MFDs. Any changes to the settings (range, gain, etc.) of the 200kHz channel one on of the MFDs is going to be echoed on the other MFD.
Find all posts by this user
Quote this message in a reply
04-12-19, 08:40 AM
Post: #5
RE: [CA11] Multiple MFDs wth 50/200 kHz sonar
Oh OK I thought the RV-100 also had chirp that used the 50/200 signal?

Thanks as always for your quick help.
Jack

Jack - MS Gulf Coast
Current Ray Equipment - Axiom 7 RV serving as DM and networked to a eS127 -
Quantum Radar via WiFi to eS127, RMK-9 networked to eS127, EV-1 Sensor Core, RV-100 and B60 transducers.
Find all posts by this user
Quote this message in a reply
04-12-19, 12:51 PM
Post: #6
RE: [CA11] Multiple MFDs wth 50/200 kHz sonar
Jack,

Negative. Please click here to view a FAQ addressing the 200W high frequency CHIRP spectrum supported by RealVision transducers.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)