Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[LW] [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
07-07-19, 08:02 AM (This post was last modified: 07-09-19 06:41 AM by Louise - Raymarine - Moderator.)
Post: #1
[LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Hallo,
Can I have information abut compatibility with the axiom 9 chart plotter with my actual instruments, st6002 autopilot and st60+ tridata and st60+ wind instrument?
Thank you .
Antonio
Find all posts by this user
Quote this message in a reply
07-11-19, 09:41 AM
Post: #2
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Dear toniocask,

Thank you for your post.

You can network the old seatalk system with the new STng system with our convertor (part no E22158). It is called the ST1 to STng convertor and the manual is viewable here.

You will not be able to control your autopilot from the Axiom when these 2 systems are networked together, you can still send waypoint and route data to the pilot just lacking the feature of pilot control.

All of your instrument data will be shared on to the STng network.

Many Thanks
Louise
Find all posts by this user
Quote this message in a reply
07-19-19, 05:45 AM (This post was last modified: 07-19-19 07:42 AM by Chuck - Raymarine - Moderator.)
Post: #3
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Many thank's.
Ciao
Find all posts by this user
Quote this message in a reply
07-19-19, 07:26 PM (This post was last modified: 07-22-19 09:44 AM by Chuck - Raymarine - Moderator.)
Post: #4
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Please claarify "you can still send waypoint and route to the pilot" ?

So it's possible to send waypoints and routes from the Axiom (w/ LH3) to an S1 Autopiot? Explain how and what does "just lacking feature of pilot control?

Note I have the E22158 converter installed.
thanks,
papa Ralph
Find all posts by this user
Quote this message in a reply
07-23-19, 03:01 AM
Post: #5
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
You are welcome.
Find all posts by this user
Quote this message in a reply
07-23-19, 03:03 AM
Post: #6
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Dear Papa Ralph,

Thank you for your post.

You can send waypoint and route data to the S1 over seatalk 1. You will not be able to enable the autopilot or select standby from the Axiom as these controls will not be available.

Many Thanks
Louise
Find all posts by this user
Quote this message in a reply
07-23-19, 11:15 AM (This post was last modified: 07-23-19 01:43 PM by Chuck - Raymarine - Moderator.)
Post: #7
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Louise, thanks for the quick response, but what I would like to know is HOW or what I have to do to get the waypoints and route to the S1 autopilot controller?

I'm new to the Axiom and don't see any menu to do this. is it done automatically? Do I have to enable some setting. I did set a waypoint on the plotter but didn't see anything on the Autopilot.

If this info gets to the Autopilot I would assume then I could have the pilot goto that waypoint, correct?

thanks again,

Ralph
Find all posts by this user
Quote this message in a reply
07-31-19, 03:53 AM
Post: #8
RE: [LW11] Axiom 9 chart plotter compatibility with st60 and st6002
Dear Papa Ralph,

Thank you for your post.

You will need to be tracking to a waypoint or following a route on the Axiom. Then press display on the ST6002 control head, you should see your
XTE, bearing to waypoint and so forth.

Many Thanks
Louise
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)