Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11] LH III Install issues
07-19-19, 01:07 PM (This post was last modified: 07-24-19 01:37 PM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11] LH III Install issues
I have an eS127, a Ray 60 VHF, a I70S, aP70R, EV-1, ACU, Raystar 130, and a Quantum Radome and two Fox MEFI's connected to two 2006 Crusader engines, a legacy DST800 (not sure why the error message below displays a DST200), and an Airmar fish finder/depth.

I have installed LH III and updated each peripheral to your latest update. I confirmed that all have the latest update. None were issues with LH II

Several issues have cropped up since.

Issue 1

I get error messages when I attempt to manually choose speed, depth, GPS, etc sources. For instance, when I attempt to select Speed source, I get the message “Manually selecting source of Speed is not supported when the following devices are on the network.

DST200 S/N 3624425
ISO: (c3 08 67 e7 1d 96 a0 c0) CAN:(1)
Raymarine i70s DisplayS/N: 0560639
E32153 S/N: 0460097
Raymarine E070245 Ray60 VHF S/N: 0360631
please consult manual for more information."

There are several messages like this, and sometimes I can go in and change one of the peripherals that I had just gotten a message on.

Since I have two GPS's, one in the eS127 and the other, a Raystar 130, I would like to be able to assign either so I can use one as a backup if there is a problem with the other.

Thanks for any help you can give.
Find all posts by this user
Quote this message in a reply
07-24-19, 01:41 PM
Post: #2
RE: [CA11] LH III issues - data source selection not supported
Welcome to the Raymarine Forum nharrison5,

The reported issue was identified and logged by Raymarine Product Support following the release of the LightHouse 3 v3.10.39 software update. Raymarine is seeking to correct this issue within a future software update. Please click here to view a FAQ addressing a workaround which may be employed within systems featuring an i70/i70S MFID or p70/p70S/p70R/p70RS autopilot control head.
Find all posts by this user
Quote this message in a reply
07-25-19, 08:05 AM (This post was last modified: 07-25-19 11:07 AM by Chuck - Raymarine - Moderator.)
Post: #3
RE: [CA11] LH III Install issues
Thanks Chuck,

When I use the work around you mention in the other thread, Will the vhf and MFD then use the same data sources as selected on the I70 and P70?

Nate
Find all posts by this user
Quote this message in a reply
07-25-19, 11:09 AM
Post: #4
RE: [CA11] LH III Install issues
Nate,

Q. When I use the work around you mention in the other thread, Will the vhf and MFD then use the same data sources as selected on the I70 and P70?
A. Yes. Please note that Data Source Selection only need be performed via one of the system's devices. The source selections chosen will then be used by the system's other devices.
Find all posts by this user
Quote this message in a reply
07-25-19, 12:17 PM (This post was last modified: 07-25-19 12:33 PM by Chuck - Raymarine - Moderator.)
Post: #5
RE: [CA11] LH III Install issues
Thanks!
Find all posts by this user
Quote this message in a reply
07-25-19, 12:33 PM
Post: #6
RE: [CA11] LH III Install issues
You're welcome.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)