10-24-16, 05:02 PM
Hello, I have P319 50/200 KHz - A80171 tansducer. It is compatible with DSM300?
Is required Raymarine Transducer Adapter Cable?
Thank you
Sergio
Is required Raymarine Transducer Adapter Cable?
Thank you
Sergio
Pages: 1 2
10-24-16, 05:02 PM
10-25-16, 09:22 AM
Welcome to the Raymarine Forum Sergio,
The A80171 version of the P319 fishfinder transducer may be adapted for use with a DSM300 by installing an 33-562-01 Raymarine Transducer Adapter Cable between the P319 transducer's plug and the DSM300.
The A80171 version of the P319 fishfinder transducer may be adapted for use with a DSM300 by installing an 33-562-01 Raymarine Transducer Adapter Cable between the P319 transducer's plug and the DSM300.
10-26-16, 08:27 PM
What are the compatible models of multifunction Touch Display?(A80171- P319 transducer) Is necessary adapter cable?
Thank you
Thank you
10-27-16, 08:03 AM
Sergio,
The A80171 version of the P319 fishfinder transducer may be directly mated to the transducer socket of an ax7, cx7, e7D, ex7, or eSx7 MFD to support 600W 50/200kHz fishfinder imaging. Alternatively, the DSM300 may be interface to any model of a/c/e/eS/gS-Series MFD any the A80171 version of the P319 fishfinder transducer may be adapted to be mated to the DSM300's Transducer socket using the adapter specified within my initial response.
The A80171 version of the P319 fishfinder transducer may be directly mated to the transducer socket of an ax7, cx7, e7D, ex7, or eSx7 MFD to support 600W 50/200kHz fishfinder imaging. Alternatively, the DSM300 may be interface to any model of a/c/e/eS/gS-Series MFD any the A80171 version of the P319 fishfinder transducer may be adapted to be mated to the DSM300's Transducer socket using the adapter specified within my initial response.
10-27-16, 09:17 PM
I have Raymarine c80 inside my boat, DSM 300, AIS 350 and A80171 P319 transducer. I would like to buy multifunction displays a67 ,a68 series or others to put in cockpit . It is possible to communicate all of these equipment? C80 with new multifunctions displays and transducer?
Thank you again
Thank you again
10-28-16, 08:25 AM
10-28-16, 09:57 AM
OK, but I could connect the transducer with a new multidisplay function in cokpit and also connect the same transducer with DSM300 (c80) inside the boat?
I would like to keep c80 inside the boat and new multifunction display on the cockpit.
Thank you again
I would like to keep c80 inside the boat and new multifunction display on the cockpit.
Thank you again
10-28-16, 10:12 AM
Sergio,
It is not possible to simultaneously interface the same fishfinder transducer to more than one device. Accordingly, the transducer may be interfaced to the DSM or to the MFD, but not to both simultaneously.
It is not possible to simultaneously interface the same fishfinder transducer to more than one device. Accordingly, the transducer may be interfaced to the DSM or to the MFD, but not to both simultaneously.
10-28-16, 10:53 AM
If I buy a multifunction display I must connect the transducer in DSM300 already installed or connect the transducer directly in MFD?
10-28-16, 02:01 PM
Sergio,
Q) If I buy a multifunction display I must connect the transducer in DSM300 already installed or connect the transducer directly in MFD?
A) Please note that 50/200kHz fishfinder transducers cannot be mated to an ax8 or eSx8 MFD's Transducer socket. You have a choice of either:
- adapting the A80171 version of the P319 fishfinder transducer transducer to permit it to be interfaced to the DSM300 and then interfacing the DSM300's SeaTalkHS socket to any model of a/c/e/eS/gS-Series MFD's Network (RayNet) socket via a cable assembly constructed from an A80272 SeaTalkHS (M) to RayNet (M) Adapter and an appropriate length of RayNet (F) to RayNet (F) Cable; or
- connecting the A80171 version of the P319 fishfinder transducer directly to the Transducer socket of an ax7, c7x, e7D, ex7, or eSx7 MFD.
Q) If I buy a multifunction display I must connect the transducer in DSM300 already installed or connect the transducer directly in MFD?
A) Please note that 50/200kHz fishfinder transducers cannot be mated to an ax8 or eSx8 MFD's Transducer socket. You have a choice of either:
- adapting the A80171 version of the P319 fishfinder transducer transducer to permit it to be interfaced to the DSM300 and then interfacing the DSM300's SeaTalkHS socket to any model of a/c/e/eS/gS-Series MFD's Network (RayNet) socket via a cable assembly constructed from an A80272 SeaTalkHS (M) to RayNet (M) Adapter and an appropriate length of RayNet (F) to RayNet (F) Cable; or
- connecting the A80171 version of the P319 fishfinder transducer directly to the Transducer socket of an ax7, c7x, e7D, ex7, or eSx7 MFD.
Pages: 1 2