[CA] [CA11] Airmar b164 and RV-100 on Axiom 7 - Printable Version +- Raymarine forum (http://forum.raymarine.com) +-- Forum: Raymarine Forums (/forumdisplay.php?fid=1) +--- Forum: Fishfinders (/forumdisplay.php?fid=25) +--- Thread: [CA] [CA11] Airmar b164 and RV-100 on Axiom 7 (/showthread.php?tid=6001) |
[CA11] Airmar b164 and RV-100 on Axiom 7 - hstechfl - 07-05-18 11:15 AM Good afternoon, I am trying to install an Airmar b164 (already installed in the boat but not being utilized) transducer to an Raymarine Axiom 7 with an RV-100. Is the correct Y-cable the A80491? Also- would all the functionality from both transducers be maintained with this setup? The reason I want the Airmar b164 installed is to get the readings in deeper water. The RV-100 usually stops reading after I get to over 600 feet. I have a DSM300 also, but from what I have read, this cannot be used with the Axiom. Any help would be appreciated RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - Chuck - Raymarine - Moderator - 07-05-18 03:50 PM Welcome to the Raymarine Forum hstechfl, Was the B164 previously used with the DSM300? Was the B164's cable terminated with a plug which permitted it to be directly (no adaptation) to the DSM300's Transducer socket? RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - hstechfl - 07-05-18 06:45 PM Hi Chuck- yes the b164 was plugged into the DSM300 direct, which was then plugged into a seatalk hs hub. I'm still using the seatalk hub to utilize an old redone ( which is working on the axiom). RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - Chuck - Raymarine - Moderator - 07-06-18 10:51 AM hstechfl, The A80492 Adaptor Cable would be used to simultaneously interface a RealVision and a DSM250/DSM30/DSM300/CP300/CP370 style transducer to an AXIOM RV MFD. RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - hstechfl - 07-06-18 11:56 AM Thanks Chuck! If I install this setup- the MFD will stop reading sonar from the RV-100 and only the b164 correct? The RV-100 will only display downvision and realvision 3D as I understand.. RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - Chuck - Raymarine - Moderator - 07-06-18 12:47 PM hstechfl, Q. If I install this setup- the MFD will stop reading sonar from the RV-100 and only the b164 correct? The RV-100 will only display downvision and realvision 3D as I understand. A. Partially correct. The resulting system would support 600W 50kHz sounder imaging, 600W 200kHz sounder imaging, RealVision 3D sonar imaging, SideVision Sonar imaging, and DownVision sonar imaging. RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - hstechfl - 07-13-18 07:14 AM Hi Chuck, Just following up with this. I installed the correct cable, but the unit keeps crashing and rebooting. It seems to only do it when I have both transducers plugged in. It does NOT do it when I have ONLY the b164 plugged in. But if I plug the RV-100 in, it crashes. It also will not see the RV-100 when it is the only one installed (on the adapter cable)- without the b164. I got it to work one time when I installed the b164 only and and set it up in the settings. I then rebooted with the RV-100 plugged in and everything worked. But shortly after when I restarted again- it crashed. Is there an additional setting I need to configure? Any help would be appreciated. Thanks RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - Chuck - Raymarine - Moderator - 07-16-18 08:11 AM hstechfl, As earlier LightHouse 3 software featured stability issues when using multiple sonar sources, such stability issues may be indicative of operating the MFD with a software version earlier than LightHouse 3 v3.5.40. If operating with an earlier version of software, then it would be recommended that the MFDs software be updated accordingly and that the system then be tested again. RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - hstechfl - 12-27-18 08:50 PM Hi Chuck, I had been up and running with the equipment described previously in this thread- until I updated my Axiom 7 to the latest software on Monday. I now cannot connect to the b164 and it does not even come up as an option to manually select. I tried to factory reset which did not work. Is there a compatibility issue with the latest software update? Thanks RE: [CA11] Airmar b164 and RV-100 on Axiom 7 - Chuck - Raymarine - Moderator - 12-28-18 10:17 AM hstechfl, When using a Y-Cable which is designed to support simultaneous use of a RealVision transducer along with a compatible 50kHz/200kHz transducer, both transducers must be connected to the Y-Cable at all times. Should only one of these transducers be interfaced to the Y-Cable, then it will not be detected by the system. Please note that the B164 transducer is produced in a number of variants, each designed to meet the specific specifications of a manufacturer and/or fishfinder ... including Raymarine fishfinding products. It is possible that the transducer's ID is not being communicated to the Axiom RV MFD. Please respond with a photo of the transducer's identification tag which clearly shows all information printed on that tag in order that we may positively identify the model of Airmar B164 transducer. |