+- Raymarine forum (http://forum.raymarine.com)
+-- Forum: Raymarine Forums (/forumdisplay.php?fid=1)
+--- Forum: General Discussions (/forumdisplay.php?fid=2)
+--- Thread: [TG] [TG11] New Raymarine user - E165 Chirp (/showthread.php?tid=7836)
[TG11] New Raymarine user - E165 Chirp - IRONMIKE - 04-02-19 11:30 PM
Hey guys,
New to the forum and Raymarine in general. Been Furuno forever, but our new boat is fitted with an E165 MFD, a 450C Chirp Module and a 1kw Chirp Trans.
Been out a few times and am pretty impressed with the unit as a whole. Just finding myself reverting back to using the 200hz mode like i wouldve with the old Furuno unit.
Seems a waste, given the potential with the unit.
Just chasing any tips or sites that can help me with set up.
Cheers in advance
Mick
RE: [TG11] New Raymarine user - E165 Chirp - Tom - Raymarine - Moderator - 04-03-19 08:21 PM
Hello Mick,
The CP450C is a good sounder, but needs to be well set-up in order to get the most from it. One key advantage of our current CP470 over the CP450C is that it's essentially a hands-free operation: it can produce as good results in Auto as the CP450C can with an experienced operator at the helm.
The CP450C was designed to be used in Chirp mode, the non-Chirp 50/200kHz channels were really only there to help new users transition across. Chirp channels will produce much finer targets than non-Chirp at the same frequency range (High Chirp compared to 200kHz for example), but this is by design and is a consequence of the much higher resolution you get from Chirp signal processing. This is how a Chirp sounder can separate the individual fish in a school, where a non-Chirp sounder will just show a blobby mass.
Users coming from non-Chirp to Chirp tend to still use high frequencies in shallower water, but because of the much higher resolution of a Chirp sounder in fact that's generally not required. Most of the transducers that were available when CP450C was shipping had a very narrow beam at High/200kHz frequency, which means that they're good for imaging the finer details of structure but don't see many fish in the water column (spotlight instead of floodlight.) If you're looking in the mid-to-upper water layers then I'd recommend using Medium or Low Chirp instead of High, even in shallow water (as shallow as 10m) because these have a much wider beam and will show you more fish.
As far as manual setup goes, my recommendation is to:
- use A-scope, Mode 2 (Right, on current systems) to measure the effects of your changes. Look at the signal levels down near the bottom, not at the surface.
- start with Gain very high (e.g. 100%), Colour Gain very low (e.g. 15%) and TVG very low (software version dependent, see the attached document)
- Looking at the A-scope, go through a cycle of Gain-down until most of the clutter is removed, then Colour Gain up until the strongest returns are just showing in red, then repeat until you have just a little clutter left down near the bottom.
- Finally, use TVG (if required) to fade out excessive near-surface clutter. From the low starting point, make the smallest change to TVG that you can because large TVG changes can suppress wanted targets in the water column.
Finally, I recommend not using the Classic White colour palette. It makes even a small amount of clutter very obvious and obtrusive. My recommendation for use in bright sunlight is the Sunburst colour palette, where clutter is pale yellow and hardly shows up against the white background but strong returns are dark red and stand out with high contrast. See the attached image for an example of why not to use Classic White: the two images use the same Gain, but the white one shows really annoying levels of clutter which would cause you to reduce Gain and lose wanted targets.
Regards,
Tom
RE: [TG11] New Raymarine user - E165 Chirp - IRONMIKE - 04-04-19 07:34 PM
Thanks so much Tom, apprieciate you taking the time to explain.
Alot of what you have said makes sense. I havent played with A scope much but have always been wanting to.
The Transducer fitted is a Airmar TM275LHW
I will have to put some research into what it is capable of also.
We really put a lot of time searching for small isolated marks which requires a good picture at slower cruise speeds. And we are usually in the 50-100m range.
Very funny to see the rationale behind the colour pallette. I always use white.. haha
Thanks again
Mick
RE: [TG11] New Raymarine user - E165 Chirp - Tom - Raymarine - Moderator - 04-08-19 02:07 AM
Hi Mick,
A CP450C, TM275LH-W and e165 should give very good results in that sort of depth. If in doubt, post back some screenshots (or, if not screenshots, then high-resolution, sharp, full-screen photos) and I'll see if there are any suggestions I can make to improve the image.
Regards,
Tom