Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11] ST60 wind sensor
04-22-20, 12:05 PM (This post was last modified: 04-22-20 02:17 PM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11] ST60 wind sensor
Greetings.

Last week, I had a nice (but probably fairly old) ST60 wind sensor at the top of my mast. It's gone now (not the cups or vane -- the whole thing!). Probably the doings of that evil Osprey I have noticed sitting on my neighbor's wind sensor...LOL (note, I love Osprey).

Three questions.

Is the attached picture a R28170 (complete unit)?

Do you make a bird spike like Windex uses (of course, the spike on my Windex has a 30 degree bend.....)

Am I likely to find other failures up there, or is it simply a case of "buy, climb mast, screw to plug/mount"? I'm hoping the attachment nut backed off and it fell down.

Thanks!

Harry


Attached File(s) Thumbnail(s)
   
Find all posts by this user
Quote this message in a reply
04-22-20, 02:34 PM (This post was last modified: 04-22-20 02:35 PM by Chuck - Raymarine - Moderator.)
Post: #2
RE: [CA11] ST60 wind sensor
Welcome to the Raymarine Forum Harry,

Q1. Is the attached picture a R28170 (complete unit)?
A1. Negative. R28170 is the part number for the standard length (14-1/2") masthead wind transducer alone. R28171 is the part number for the long length (26") masthead wind transducer alone. Both will fit the currently installed masthead block should it still be in place. If seeking the wind transducer, masthead block, and cable, then the part numbers are E22078 (30m) and E22079 (30m) depending upon whether you will want the standard length transducer with a masthead block and 30m or or long length transducer with a masthead block and 30m cable respectively.

Q2. Do you make a bird spike like Windex uses (of course, the spike on my Windex has a 30 degree bend.....)
A2. Negative.

A3. Am I likely to find other failures up there, or is it simply a case of "buy, climb mast, screw to plug/mount"?
A3. Unfortunately, the only way to know would be to inspect the transducer's masthead block by sending someone up the mast, lowering the mast, or perhaps by using a UAV (drone) with high def camera should you have access to one or know someone who does and is willing to assist.
Find all posts by this user
Quote this message in a reply
04-23-20, 10:40 AM
Post: #3
RE: [CA11] ST60 wind sensor
Chuck,

Thanks for the replies. Most were as expected, but still helpful.

The surprise, and I'm glad you pointed it out, is the long vs short arm.

For a cruising 43' sailboat, would you recommend the long or the short? I can't compare with the original.....LOL.

I suspect the short will be more robust, but get slight interference from the sails, a tradeoff that is probably appropriate for a cruiser. Thoughts?

Thanks

Harry
Find all posts by this user
Quote this message in a reply
04-23-20, 11:07 AM
Post: #4
RE: [CA11] ST60 wind sensor
Harry,

Performance sailors will seek the cleanest air, necessitating that the wind transducer be positioned as far as is permissible from objects which will alter the wind's natural path. This group will commonly seek a long arm wind transducer. For non-performance applications, the standard arm wind transducer will generally suffice.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)