Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11] ST4000+ Drive Power Supply
02-04-20, 11:33 PM (This post was last modified: 02-05-20 11:37 AM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11] ST4000+ Drive Power Supply
Hello,

Currently my ST4000+ has a 12V connection and the drive motor is powered from ST4000+.

I am reconfiguring my system to add SeaTalkNG network.

Can ST4000+ be powered from SeaTalkNG and still provide power to the drive., or should the ST4000+ be directly connected to 12V power supply so that the drive is not getting power from SeaTalkNG?

If I have to connect 12v power directly to St4000+ and still communicate on SeaTalkNG then I would have to remove power from the spur cable to ST4000+. What is the detailed procedure for this? The SeaTalkNG will already have a power supply.

I've attached an image of my proposed configuration.

Thanks!

Andy
Find all posts by this user
Quote this message in a reply
02-05-20, 11:59 AM (This post was last modified: 02-06-20 02:10 PM by Chuck - Raymarine - Moderator.)
Post: #2
RE: [CA11] ST4000+ Drive Power Supply
Welcome to the Raymarine Forum Andy,

Q1. Can ST4000+ be powered from SeaTalkNG and still provide power to the drive.,
A1. Negative. The ST4000+ is neither designed be powered by a SeaTalk bus, nor a SeaTalkng backbone.

Q1b. should the ST4000+ be directly connected to 12V power supply so that the drive is not getting power from SeaTalkNG?
A1b. Affirmative. Additionally and as indicated within the FAQ on this subject, the red lead of the SeaTalk Cable connecting the ST4000+ to the SeaTalk bus / SeaTalk to SeaTalkng Converter should be severed and then insulated to prevent shorting.

Q2. If I have to connect 12v power directly to St4000+ and still communicate on SeaTalkNG then I would have to remove power from the spur cable to ST4000+. What is the detailed procedure for this? The SeaTalkNG will already have a power supply.
A2. Please refer to the FAQ referenced within the response to Q1b.

Q3. I've attached an image of my proposed configuration.
A3. No configuration diagram has been attached to your thread. Should you desire for it to be reviewed, please attach the diagram to a follow-up post to this thread.
Find all posts by this user
Quote this message in a reply
02-06-20, 10:51 AM (This post was last modified: 02-06-20 11:44 AM by Chuck - Raymarine - Moderator.)
Post: #3
RE: [CA11] ST4000+ Drive Power Supply
Hi Chuck diagram attached. I have not drawn the power supply to ST4000+.

Hope all looks I start my install this weekend!

Andy


Attached File(s) Thumbnail(s)
   
Find all posts by this user
Quote this message in a reply
02-06-20, 11:52 AM
Post: #4
RE: [CA11] ST4000+ Drive Power Supply
Andy,

The diagram appears to be correct in all but the following aspects:

- the i60 Wind is shown connected to a backbone (blue) socket ... should be connected to a spur (white) socket.

- shift the SeaTalkng Power Cable to the other side of the 5-Way Connector to create a more balanced LEN load.

- annotate the diagram with my comments addressing how the ST4000+ should be interfaced to the SeaTalk to SeaTalkng Converter.
Find all posts by this user
Quote this message in a reply
02-06-20, 01:07 PM (This post was last modified: 02-06-20 02:09 PM by Chuck - Raymarine - Moderator.)
Post: #5
RE: [CA11] ST4000+ Drive Power Supply
Hi again Chuck - man you have been so helpful - I can't thank you enough!

Here is updated diagram as per your suggestions.

Andy


Attached File(s) Thumbnail(s)
   
Find all posts by this user
Quote this message in a reply
02-06-20, 02:10 PM
Post: #6
RE: [CA11] ST4000+ Drive Power Supply
Andy,

Great job with the diagram!
Find all posts by this user
Quote this message in a reply
02-06-20, 02:25 PM
Post: #7
RE: [CA11] ST4000+ Drive Power Supply
Hi Chuck thanks again for all your help!

Now comes the fun part - running wires!

Regards,

Andy
Find all posts by this user
Quote this message in a reply
02-06-20, 02:30 PM
Post: #8
RE: [CA11] ST4000+ Drive Power Supply
You're welcome.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)