Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11[ ST60 Windvane Replacement #22012 question
02-05-20, 05:11 PM (This post was last modified: 02-06-20 10:51 AM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11[ ST60 Windvane Replacement #22012 question
Hi,
Can I replace the entire windvane model 22012 (square cup model) with the newer round cup model 28170?
Will the 28170 fit the mount and attach to the older 22012 mount ok.
See my pictures of the 22012 with small set screw that acts to align plug.
I read I may have to make a speed setting adjustment and remove an O ring.


Attached File(s) Thumbnail(s)
       
Find all posts by this user
Quote this message in a reply
02-06-20, 10:52 AM
Post: #2
RE: [CA11[ ST60 Windvane Replacement #22012 question
Welcome to the Raymarine Forum a1sailor,

What model of wind instrument is the wind vane presently interfaced to?
Find all posts by this user
Quote this message in a reply
02-07-20, 08:15 AM (This post was last modified: 02-07-20 08:34 AM by Chuck - Raymarine - Moderator.)
Post: #3
RE: [CA11[ ST60 Windvane Replacement #22012 question
The existing vane is interfaced with the Raymarine ST 60 display.
Thanks
Find all posts by this user
Quote this message in a reply
02-07-20, 09:14 AM
Post: #4
RE: [CA11[ ST60 Windvane Replacement #22012 question
a1sailor,

As indicated within the FAQ found here, although possible, it would be recommended that the ST50 masthead block and cable be replaced with the currently produced masthead block and cable to avoid possible damage to the replacement masthead wind transducer's pins.
Find all posts by this user
Quote this message in a reply
02-07-20, 09:32 AM (This post was last modified: 02-07-20 09:52 AM by Chuck - Raymarine - Moderator.)
Post: #5
RE: [CA11[ ST60 Windvane Replacement #22012 question
Hi Chuck,
The existing unit is ST60 not an ST50. The existing mast mounted receptacle unit does have a key slot, the vane has a set screw that appears to act as a key to fit into the mast mounted receptacle unit for alignment purposes. Please see picture sent in 1st post.

Are you saying my existing vane is an ST50 version?
The part # on the existing vane is : A22012
Find all posts by this user
Quote this message in a reply
02-07-20, 09:54 AM
Post: #6
RE: [CA11[ ST60 Windvane Replacement #22012 question
a1sailor,

I understand that the instrument may be a ST60 Wind instrument. However, the photos of the masthead wind transducer are those of a ST50 / ST290 masthead wind transducer.
Find all posts by this user
Quote this message in a reply
02-07-20, 12:34 PM (This post was last modified: 02-07-20 12:50 PM by Chuck - Raymarine - Moderator.)
Post: #7
RE: [CA11[ ST60 Windvane Replacement #22012 question
I did not realize vane was ST 50 version. It does have a "key" and a "keyway" on mast mount. With this feature should the newer vane version align pins properly and attach to mast mount. Please see new pic of existing "key" on existing vane.
Thank you


Attached File(s) Thumbnail(s)
   
Find all posts by this user
Quote this message in a reply
02-07-20, 01:04 PM
Post: #8
RE: [CA11[ ST60 Windvane Replacement #22012 question
a1sailor,

As indicated within my earlier response, although possible, it would be recommended that the ST50 masthead block be replaced. That said, should your currently installed masthead block accept the masthead transducer's key, then it may be retained for use with the currently offered E22078 Masthead Wind Transducer.
Find all posts by this user
Quote this message in a reply
02-07-20, 02:55 PM (This post was last modified: 02-07-20 02:57 PM by Chuck - Raymarine - Moderator.)
Post: #9
RE: [CA11[ ST60 Windvane Replacement #22012 question
Thank you, this is helpful.
Regards.
Find all posts by this user
Quote this message in a reply
02-07-20, 02:58 PM
Post: #10
RE: [CA11[ ST60 Windvane Replacement #22012 question
You're welcome.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 2 Guest(s)