Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11] Raymarine C95 displays incorrect apparent wind speed
04-09-20, 03:25 AM (This post was last modified: 04-09-20 12:22 PM by Chuck - Raymarine - Moderator.)
Post: #1
Exclamation [CA11] Raymarine C95 displays incorrect apparent wind speed
I have a 2015 Raymarine C95 MFD connected to a 2005 Raymarine C70 MFD via NMEA0183 at 4800 baud.
The C70 has a Seatalk (1) network connected to a Raymarine Wind Speed instrument ST60+.
The wind speed shows correct apparent wind direction and speed on its display as does the C70.
The C95 shows direction accurately but the wind speed shows about 3 knots when the instrument shows about 5.6 knots. The ratio between the speeds is about the same over different wind speeds.
The C95 is getting the wind speed and direction via the same NMEA0183 sentence MWV.
I disabled all NMEA0183 sentences from the C70 apart from the MWV output and observed the sentence received on the C95. It showed the correct speed and angle and measurement in knots, while the C95 display showed an incorrect speed also in knots.
To me this showed that the C95 is using the MWV and that it is receiving the correct value but displaying an incorrect value.
My assumption is that the C95 has a bug in its display software.
The C95 uses the Lighthouse II operating system. The version in the C95 was old so I downloaded the latest version (R19) and updated the C95. I searched the revision notes for mention of wind speed and found nothing.
Same problem of incorrect apparent wind speed with version 19.
I searched the Raymarine Forum and found nothing relevant.
I find it hard to believe that no one has reported the same problem so I checked the following:
The C95 is set to knots and the MWV message shows knots.
Perhaps the C95 is very intelligent and is translating mast head speed to cockpit (ground) speed? So I checked the boat setup to see if there is a setting for mast height. There is none, so perhaps there is a factor that its using?
Next I searched the C95 users manual and found a setting for wind damping. This setting affects both angle and wind speed. 1 is the slowest and 15 is the fastest, the default is 12. My C95 is set to 12 for both speed and angle.Changing it to 15 made no difference.
Any suggestions?
Find all posts by this user
Quote this message in a reply
04-09-20, 01:07 PM (This post was last modified: 04-09-20 01:08 PM by Chuck - Raymarine - Moderator.)
Post: #2
RE: [CA11] Raymarine C95 displays incorrect apparent wind speed
Welcome to the Raymarine Forum Jack,

Please note that interfacing the products listed would typically be accomplished fia a SeaTalk to SeaTalkng Converter Kit. That said, please click here to view a FAQ addressing how to record NMEA 0183 sentences received (RX) by the c95 MFD. When the reported problem is manifesting itself, please verify that the ST60 instrument has been configured to report apparent rather than true wind data. Please additionally ensure that the MFDs have been interfaced in a manner which would only support one way communications ... from the C-Series Classic MFD to the c95 MFD, as bidirectional NMEA 0183 communications may result in a data loop, which in turn may cause there reported symptom. If conditions have been verified and the problem persists, then use the NMEA 0183 buffer recording feature to record approximately ten seconds of data to a microSD memory card. After doing so, please attach the recorded NMEA 0183 buffer file to this thread for further analysis.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)