Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
(DG) Axiom Pro LH3 & LH2
02-17-18, 05:34 AM (This post was last modified: 02-19-18 09:40 AM by Derek - Raymarine - Moderator.)
Post: #1
(DG) Axiom Pro LH3 & LH2
I am in the process of fitting an Axiom Pro rv3d and will install LH3 software. I also have 2 No. ES98`s with LH2. They will all run through the network switching with radar & ais. My question is can will they all still talk to each other and be ok ?

Kk
Find all posts by this user
Quote this message in a reply
02-19-18, 09:45 AM
Post: #2
RE: (DG) Axiom Pro LH3 & LH2
Hi SIESTA BOTNIA

Thank you for your enquiry.

The recent release of LHIII software, click here for details will enable eS Series displays to be updated to LHIII. Once the eS Series displays are running LHIII, they can be connected to the AXIOM via the standard RayNet cabling and HS5 Network Switch.

They will all then share data, charts, radar, Realvision features and functionality.

Please read the notes carefully so that you know what features and functions to expect with LHIII compared to LHII.
Regards
Find all posts by this user
Quote this message in a reply
02-20-18, 02:20 PM
Post: #3
RE: (DG) Axiom Pro LH3 & LH2
[quote='Derek - Raymarine - Moderator' pid='16821' dateline='1519051521']
Hi D,

I would like to run the 2 No. ES98`s on LH2 as fuel manager & Volvo engine data are very important plus I am used to the units. I am going to use the Axiom pro LH3 for 3D f/Finder + charts. My ? is will the radar, ais & pilot signals show up on the 2 No. ES LH2 & the Axiom LH3 through the network, I don't expect the Axiom 3D RV to show on the ES units. All equipment/kit is less than a year old.

Regards
Kk
Find all posts by this user
Quote this message in a reply
02-21-18, 01:38 AM
Post: #4
RE: (DG) Axiom Pro LH3 & LH2
[quote='Derek - Raymarine - Moderator' pid='16821' dateline='1519051521']
Hi D,

I would like to run the 2 No. ES98`s on LH2 as fuel manager & Volvo engine data are very important plus I am used to the units. I am going to use the Axiom pro LH3 for 3D f/Finder + charts. My ? is will the radar, ais & pilot signals show up on the 2 No. ES LH2 & the Axiom LH3 through the network, I don't expect the Axiom 3D RV to show on the ES units. All equipment/kit is less than a year old.

Regards
Kk
Find all posts by this user
Quote this message in a reply
02-21-18, 07:41 AM
Post: #5
RE: (DG) Axiom Pro LH3 & LH2
Hi KK

You cannot run both LHII and LHIII units on the same RayNet network, in fact even connecting them via STng will trigger constant DATA MASTER alarms and so we really do not recommend this.

You would be better to seperate the LHII units and keep radar, AIS and pilot on the AXIOM.
Thanks
Find all posts by this user
Quote this message in a reply
02-21-18, 09:10 AM
Post: #6
RE: (DG) Axiom Pro LH3 & LH2
Ok -

Can I run the AXIOM PRO RV on the new LH3 software and run the ES98`S on LH3 on there version and still network them all together so they all share pilot, radar etc ? Obviously the 3dRV will be Axiom only.

Will the Axiom give me engine data from a Volvo d6 as it was available on the ES98 ?

Kk
Find all posts by this user
Quote this message in a reply
02-21-18, 11:28 AM
Post: #7
RE: (DG) Axiom Pro LH3 & LH2
hi KK,

yes, the engine data can be viewed on the AXIOM with LHIII, then the ES displays updated to LHIII too so you can then have an integrated system again.
Thanks
Find all posts by this user
Quote this message in a reply
02-21-18, 11:48 AM
Post: #8
RE: (DG) Axiom Pro LH3 & LH2
Hi Derick,

Thanks for your help.

Just down loaded all ES/Axiom LH3 software as going to power up tomorrow. Soon find out if it all works !!!

Kk
Find all posts by this user
Quote this message in a reply
02-21-18, 11:54 AM
Post: #9
RE: (DG) Axiom Pro LH3 & LH2
Hi kk

hope it goes well
thanks
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)