Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[DG] [DG] smartpilot s3
01-21-19, 07:14 AM (This post was last modified: 01-21-19 07:47 AM by Derek - Raymarine - Moderator.)
Post: #21
RE: [DG] smartpilot s3
Hi thanks Derek
it has the conation thanks
Ricardo
Find all posts by this user
Quote this message in a reply
01-21-19, 07:50 AM
Post: #22
RE: [DG] smartpilot s3
Hi Ricardomann,

Thanks for the feedback,

If I understand your message, the smartpilot has the Solenoid connections and bypass valve connections?

Thanks
Derek
Find all posts by this user
Quote this message in a reply
01-21-19, 09:22 AM (This post was last modified: 01-21-19 09:23 AM by Derek - Raymarine - Moderator.)
Post: #23
RE: [DG] smartpilot s3
Hi yes it has the same conetions and the same wiring diagram
for constant running pump or engine pump
thanks Ricky
Find all posts by this user
Quote this message in a reply
01-21-19, 09:28 AM
Post: #24
RE: [DG] smartpilot s3
Hi Ricardomann

OK, so do you need any further information?

Regards
Derek
Find all posts by this user
Quote this message in a reply
01-21-19, 09:33 AM (This post was last modified: 01-21-19 09:47 AM by Derek - Raymarine - Moderator.)
Post: #25
RE: [DG] smartpilot s3
i should be ok
i am going to test
if not ok i will get back on to you
thanks again Ricardo
Find all posts by this user
Quote this message in a reply
01-21-19, 09:47 AM
Post: #26
RE: [DG] smartpilot s3
Hi Ricardomann,
OK, understood,
best regards
Derek
Find all posts by this user
Quote this message in a reply
01-21-19, 08:14 PM (This post was last modified: 01-22-19 09:38 AM by Chuck - Raymarine - Moderator.)
Post: #27
RE: [DG] smartpilot s3
Hi Derek
cannot get my axiom 9 to se my autopilot
wont let me enable

just testing on bench
axiom 9 won't respond to smart pilot S3 ST6001

thanks Ricardo
Find all posts by this user
Quote this message in a reply
01-22-19, 10:15 AM
Post: #28
RE: [DG] smartpilot s3
Hi Ricardomann

The AXIOM will only interface and directly control the current generation of autopilots - that is to say the Evolution series. the smartpilot was designed many years ago and so the AXIOM does not recognise it.

The AXIOM cannot be used to control the operation of the autopilot, course changes or STANDBY or AUTO mode, the AXIOM can, however, still be used to send route following information to the Smartpilot. The link here provides information relating to interfacing legacy autopilots to AXIOM, this link here describes operation in TRACK mode between AXIOM and a legacy autopilot.

regards
Derek
Find all posts by this user
Quote this message in a reply
01-22-19, 10:31 AM (This post was last modified: 01-22-19 10:34 AM by Derek - Raymarine - Moderator.)
Post: #29
RE: [DG] smartpilot s3
Hi i get you. my smattered pilot reads from axiom and reacts to the data only ? thanks rick
Find all posts by this user
Quote this message in a reply
01-22-19, 10:37 AM
Post: #30
RE: [DG] smartpilot s3
Hi Ricardomann,
Yes - correct, the smartpilot will accept track information from the AXIOM via the STng to SeaTalk1 converter.
Thanks
Derek
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)