Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[CA] [CA11] Matrix GX2100 to eS Series 128 NMEA 0183 wiring
07-22-19, 05:05 PM (This post was last modified: 07-26-19 03:23 PM by Chuck - Raymarine - Moderator.)
Post: #1
[CA11] Matrix GX2100 to eS Series 128 NMEA 0183 wiring
PROBLEM: AIS targets are not displaying on the chart. I'm not sure the wiring is correct for port 1 and port 2 between the gx2100 and the eS128. I spoke to Standard Horizon and they advised:

-The 2100 receives GPS data on the Blue wire. This is an input to the radio. Connect the TX(+), Data Out wire of the GPS.

-The Green wire should be attached to TX (-), RX (-) and or ground. Connect this to the black ground wire or (-) wires on the GPS.

-The output of DSC will occur on the Gray wire at 4800 speed. Output leaving the radio. Connect this to the RX(+), Data In GPS wire.

-The output of AIS will occur on the Brown wire at 38400. Output leaving the radio. Connect to a different RX(+) than the one used above. The GPS needs to be setup for NMEA 0183 (38400 baud rate) in this installation. This must be a different input port than the one used for DSC.


Here's how the eS128 is currently wired:

GX2100 to eS128
Blue (TX+) to Yellow Receive + Port 1 4800 Baud
Green (TX-) to Brown Output - Port 1 4800 Baud
Green (TX-) to Green Input - Port 1 4800 Baud
Gray (Output) to White Receive + Port 1 4800 Baud
Brown (RX+) to Orange/White Receive + Port 2 38400 Baud

Is this wiring correct? Other than turning AIS on the eS128 and configuring ports 1 and 2 to the correct baud rates, are there other options that must be set to specific values to display targets on screen?

Thanks for the assistance from this group.
Find all posts by this user
Quote this message in a reply
07-26-19, 03:43 PM (This post was last modified: 07-26-19 03:45 PM by Chuck - Raymarine - Moderator.)
Post: #2
RE: [CA11] Matrix GX2100 to eS Series 128 NMEA 0183 wiring
Welcome to the Raymarine Forum Jim,

For DSC support:
GX2100 4800 NMEA 0183 IN+ (blue) to MFD Port 1 NMEA 0183 OUT+ (yellow)
GX2100 NMEA 0183 Ground (green) to MFD Port 1 NMEA 0183 OUT- (brown)
GX2100 4800 NMEA 0183 OUT+ (gray) to MFD Port 1 NMEA 0183 IN+ (white)
GX2100 NMEA 0183 Ground (green) to MFD Port 1 NMEA 0183 IN- (green)

For GX2100s w/internal AIS receiver, additionally:
GX2100 38400 NMEA 0183 OUT+ (brown) to MFD Port 2 NMEA 0183 IN+ (orange/white)
GX2100 NMEA 0183 ground (green) to MFD Port 2 NMEA 0183 IN- (orange/green)

MFD NMEA 0183 Port 2 configured to "AIS 38400"

- Configure the MFD's NMEA 0183 Port 1 Setting (HOME->SET-UP->SYSTEM SETTINGS->NMEA SET-UP->NMEA INPUT PORT 2) to NMEA 4800.
- Configure the MFD's NMEA 0183 Port 2 Setting (HOME->SET-UP->SYSTEM SETTINGS->NMEA SET-UP->NMEA INPUT PORT 2) to AIS 38400.
- To view AIS objects within the MFD's Chart application, configure the AIS overlay (MENU->PRESENTATION->OVERLAYS->AIS) to ON.
- Verify that the MFD has acquired a GPS position FIX

Should the above have been satisfied, then examine the MFD's Port 1 RX buffer to verify that $AIVDM NMEA 0183 sentences are being received from the GX2100.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 1 Guest(s)