Threaded Mode | Linear Mode

***Chuck - Raymarine - Moderator***

Welcome to the Raymarine Forum Randar,

Q1. Radar - Have the Quantum 24 Radar...Is there a way to Hardwire the Radar to the MFD?
A1. The methods for interfacing a Quantum radome to an Axiom MFD are identical to those for interfacing an a/c/e/eS/gS-Series MFD to a Quantum radome. Those seeking a wired connection to a Quantum Radome must purchase a Quantum Q24C Radome w/Wi-Fi and Ethernet interfaces rather than the Quantum Q24W Radome w/Wi-Fi interface only. Please click here to view a FAQ addressing this subject.

Q2. If I connect a RayTalkNG Cable between the two MFD's, can they share data?
A2. In order for the MFDs to share all resources and features, the MFDs must be interfaced to one another via Ethernet. As Axiom MFDs feature only one Ethernet Network communications interface and your are seeking to interface at least three devices (2 MFDs and Quantum radome) via wired Ethernet, a HS5 RayNet Network Switch must be installed onboard. Each MFD and the Quantum radome would then be interfaced to the switch.

Q3. The wiring diagram seems to show that the NMEA connector shares power...Only wire showing is the Grounding "Drain" wire. So if my NMEA Backbone is powered, it should provide power to the MFD's, correct?
A3. No. The Axiom MFDs are neither designed to be powered by a SeaTalkng backone nor to power a SeaTalkng backbone. The MFDs must be powered via the supplied Power/NMEA 2000 Cable. The SeaTalkng backbone will be powered vis a SeaTalkng Power Cable installed within a spur socket positioned at the approximate midpoint of the backbone's LEN load. Please click here to view a FAQ addressing marine electronics drain leads.

Q4. There have been a bunch of posts on here about Navionics Platinum + Have we figured out if the new Axioms will support ALL of the data?
A4. The initial release of LightHouse 3 software will not support Freshest Data Update subscription status notifications, Dock-To-Dock Autorouting, Find Nearest, Navionics Plotter Sync via the Navionics Boating app, Tide/Current graphs (current tide height and current direction/speed will be reported), 3D Chart mode, sonar logging, and SonarChart Live features. It is expected that these features will be included within a future LightHouse 3 software update.

Q5. AIS - I am using the EM-Track B100 Transceiver...Anyone see any issues with this? I have a dedicated AIS Ant and The B100 comes with the GPS Ant.
A5. No. As the system will feature more than one source of GPS data, then Data Sources feature will need to be used to specify which GPS data source will be utilized by the Raymarine system.

Q6. GPS Will the two MFD's share the data over the NMEA Net for my GPS 150 sensor?
A6. GPS data (not to be confused with cartography) will be shared via devices which have been interfaced to a SeaTalkng / NMEA 2000 backbone. See the response to Q1 regarding the recommendation that the MFDs be interfaced to one another via Ethernet communications.

Q7. Do I need a dedicated Heading sensor for Radar Overlay?
A7. No. Quantum MFDs are no different from the a/c/e/eS/gS-Series MFDs with respect to radar overlay requirements. Please click here to view a FAQ addressing this subject.

Q8. If I am using Axiom #2 as a dedicated Chartplotter/Radar Repeater (Axiom #1 is Sonar Dedicated)...Am I wasting a chance to set this up better? COuld I get better resolution and data from a different MFD?
A8. No. For maximum flexibility and a level of system redundancy, it is recommended that the MFDs be interfaced via Ethernet communications to permit either MFD to support radar, chartplotter, and fishfinder features.