Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Autopilot control head and course computer
01-27-17, 07:30 AM (This post was last modified: 01-27-17 12:22 PM by Chuck - Raymarine - Moderator.)
Post: #1
Autopilot control head and course computer
I have a Luhrs Tournament 400 and the Cetrek autopilot needs replacing. All the other electronics are Raymarine, E90W, C70 and DS600x so I am going the used Raymarine route. Can anyone advise in simple terms the differences between 7001, 7002, 8001, 8002, st70 and p70 head units?

Do they all interface with older course computers?
Find all posts by this user
Quote this message in a reply
01-27-17, 01:04 PM (This post was last modified: 01-27-17 05:28 PM by Chuck - Raymarine - Moderator.)
Post: #2
RE: Autopilot control head and course computer
Welcome to the Raymarine Forum whittj1,

Please note that ST600x, ST700x, and ST800x autopilot control heads are no longer available and that parts and service are no longer available for these autopilot control heads. These autopilot control heads were compatible with a wide range of autopilot course computers up through Raymarine's SPX autopilot course computers. The ST600x autopilot control heads were designed to provide support for autopilot installed on both power driven and sailing vessels. ST700x and ST800x autopilot control heads differentiate themselves from the ST600x autopilot control heads in that they had larger displays, supported more data pages, and featured additional buttons to provide quicker access to the most commonly used autopilot features (ex. Response, etc.). The ST700x autopilot control head was primarily intended for use onboard sail driven vessels, while the ST800x autopilot control head, with its steering knob (replaces +/-1 and +/-10 dodge buttons found on the ST600x and ST700x), was primarily intended for use onboard power driven vessels. These autopilot control heads will also support use with the retired Type 150, Type 300, S1/S1G/S2/S2G/S3/S3G, and SPX5/10/30 autopilot course computers

The ST70 Autopilot Control Heads were introduced to support Raymarine's SPX autopilot course computers and like the ST600x autopilot control heads, were designed to provide support for autopilot installed on both power driven and sailing vessels. These autopilot control heads will also support use with the retired Type 150, Type 300, and S1/S1G/S2/S2G/S3/S3G autopilot course computers.

The p70/p70S and p70R/p70RS Evolution Autopilot Control Heads were introduced with and are required for use with and Evolution Autopilot system. Like the ST800X autopilot control heads, the p70R/p70RS Evolution Autopilot Control Heads also feature a steering knob (replaces +/-1 and +/-10 dodge buttons found on the p70/p70S), and is primarily intended for use onboard power driven vessels. The p70/p70S and p70R/p70RS Evolution Autopilot Control Heads will also support use with the Type 150, Type 300, S1/S1G/S2/S2G/S3/S3G, and SPX5/10/30 autopilot course computers.

As there is limited or no ability to obtain parts service for some retired autopilot course computers and the performance of the Evolution autopilots very much exceeds that of earlier Raymarine autopilot designs, it is strongly recommended that those seeking an autopilot for their vessel consider purchasing and installing an Evolution autopilot for the vessel. The Evolution autopilots are either compatible or may be adapted for use with the equipment which you have listed.
Find all posts by this user
Quote this message in a reply
01-27-17, 04:53 PM (This post was last modified: 01-27-17 04:59 PM by Chuck - Raymarine - Moderator.)
Post: #3
RE: Autopilot control head and course computer
Thanks Chuck.
Find all posts by this user
Quote this message in a reply
01-27-17, 05:00 PM
Post: #4
RE: Autopilot control head and course computer
You're welcome.
Find all posts by this user
Quote this message in a reply
06-20-17, 12:21 PM
Post: #5
RE: Autopilot control head and course computer
I got a S2G computer and now I'm going to add a rudder sensor. Are the E70099 and

M81105 both compatible?
Find all posts by this user
Quote this message in a reply
06-20-17, 01:14 PM
Post: #6
RE: Autopilot control head and course computer
whittj1,

Q. Are the E70099 and M81105 both compatible?
A. Yes. The E70099 ACU200 and M81105 Rudder Reference Transducer are indeed compatible with and recommended for use with one another.
Find all posts by this user
Quote this message in a reply
Post Reply 


Forum Jump:


User(s) browsing this thread: 2 Guest(s)